Functional Test (FCT)
=====================

	* Connect fixture (bed‑of‑nails/connectors); run defined scripts
	* Typical coverage:
		* Current consumption in run/standby
		* Digital I/O, pull‑ups/downs
		* Analog paths (ADC/DAC linearity, references)
		* Communications (Wi‑Fi)
		* Sensors/actuators simulated or attached
		* Memories (EEPROM/Flash/RAM) read/write
		* Safety features (watchdog, brown‑out)
	* Limits and pass/fail per test instruction
	* Auto‑attach test results to SN and archive (Form F1, add log)
	
Equipment
---------

    * Thermometer for measuring room temperature
    * Cube magnet for wind direktion sensor test
    * Cylinder magnet for wind speed sesnsor test
    * Protection cover with marked positions for magnets
    * Actual Chrome web browser on PC
    * Same equipment as before
    
Test conditions
---------------

    * Successfully completed flash procedure
    * WiFi login in MyBoat
    * Same elektrical conditions as before
    * Set power source 12V
    
Functional test procedure
-------------------------

    **1. Attach protective cover**
    
    **2. Opening the website with web browser:** `http://windsensor-0.local/devinfo`_
	
.. _http://windsensor-0.local/devinfo: http://windsensor-0.local/devinfo
	
	**3. Check the firmware version**
		* V1.20
	
	.. image:: ../pics/Device_Info.png
	   :scale: 80%		   
	Fig.: Web page devinfo
    
    **4. Check WiFi connection quality (CQ: > 90% by short distance between router and PCB)**
    
    **5. Check realistic room temperature**
        * Check value **Device Temperature** app. room temperature + 10°C
        
    **6. Check wind direction sensor on position 1 with cube magnet (note polarity)**
        * Check value **Wind Direction**
        * Values ​​must change by 90° for a 90° magnet change
        * Angle values ​​must cover 0...360°
        * Offset is uncritical
	
	.. image:: ../pics/Install_Windsensor_Yachta.png
		   :scale: 50%		   
	Fig.: Test positions on PCB	
        
    **7. Check wind speed sensor on position 2 with cube magnet (note polarity)**
        * Check value **Sensor 1 (Speed)**
        * Without magnet = 1
        * With magnet = 0
        
    **8. Access the Yachta instrument page and check**
		* `http://windsensor-0.local/windi`_
		* Pointer must move slightly
		
	.. image:: ../pics/Windsensor_Instrument.png
	   :scale: 80%		   
	Fig.: Web page devinfo
		
.. _http://windsensor-0.local/windi: http://windsensor-0.local/windi	
	
	**9. Access the JSON page and save the extract (optional)**
		* `http://windsensor-0.local/json`_
		
.. _http://windsensor-0.local/json: http://windsensor-0.local/json
    
    **10. Disconnect PCB**
	
	**11. Label the firmware version on the PCB backside**

	.. image:: ../pics/Firmware_Version.jpg
		   :scale: 20%		   
	Fig.: Firmware version

Acceptance
----------

    * WiFi connection established
    * WiFi connection quality > 90%
    * Dispaying correct web page (error free)
    * Correct page change
    * Page refresh < 1 s
    * Realistic temperature values (not perfect and with offset)
    * 0...360° values for wind direction sensor
    * 0/1 change for wind speed sensor
    * Current consumption < 35 mA at 12V
	* Label for firmware version is placed